SEKURE Paradox Digiplex DGP-610 Instalační příručka stáhnout pdf (Strana 29)

EVO Control Panel 25

sequentially, skipping any disabled numbers and stopping once all selected

telephone numbers have been reached. If the control panel still fails to

report to a monitoring station telephone number after reaching the

Maximum Dialing Attempts (see section 9.8.1 on page 25), the control

panel will dial the selected backup telephone number. For each section

enable or disable the options:

(default = only option [1] enabled)

9.8.1 Maximum Dialing Attempts*

SECTION [3056]

(default = 008) The number (001 to 255, 000 = 8 attempts) programmed

into section [3056] determines how many tries before proceeding to the

next number. Also refer to section 9.8.3.

* UL Note: For UL Listed systems, the maximum dialing attempts must be set

to 5 to 10 attempts between the EVO’s two telephone lines.

9.8.2 Delay Between Dialing Attempts

SECTION [3054]

(default = 020) This delay can be set from 001 to 127 seconds.

9.8.3 Alternate Dialing Option

SECTION [3037]: OPTION [6]

(default = disabled) When enabled, the control panel dials the selected

backup telephone number after every failed attempt to contact a monitoring

station telephone number. When disabled, the control panel dials the

backup telephone number after the Maximum Dialing Attempts (see section

9.8.1) to one monitoring station telephone number fail.

9.9 Pager Delay

SECTION [3057]

(default = 020) When using the Pager Reporting Format (see section 9.7.6),

the control panel will wait for the delay period programmed into section

[3057] before uploading the report codes to the pager. Enter any value

between 001 and 127 to determine Pager Delay in seconds.

9.10 Recent Close Delay

(default = 000) If an alarm is generated within the programmed period after

arming the partition, the control panel will transmit the Recent Close report

code programmed into section [3933]. Enter any value between 001 and

255 to determine Recent Close Delay in seconds.

9.11 Power Failure Report Delay

SECTION [3058]

(default = 030) The control panel will delay the transmission of the AC

Failure report code programmed into section [3941] by the period

programmed into section [3058]. Enter any value between 001 and 255 to

determine Power Failure Report Delay in minutes.

9.12 Power Failure Restore Report Delay

SECTION [3060]

(default = 030) The control panel will delay the transmission of the AC

Failure Restore report code programmed into section [3972] by the period

programmed into section [3060]. Enter any value between 001 and 255 to

determine Power Failure Restore Report Delay in minutes.

9.13 Repeat Pager Report Code Transmission

SECTION [3059]

{default = 000) This feature re-sends the report code as specified.

9.14 Auto Test Report

SECTION [3037]: OPTIONS [3] AND [4] AND

SECTIONS [3040], [3041], [3042] AND [3043]

The control panel can transmit the test report code programmed into

section [3902] every hour or after a period of time.

9.15 Disarm Reporting Options

(default = disabled) When disabled, the control panel sends the Disarming

Report Codes (see section 9.2 on page 22) every time the partition is

disarmed. When enabled, the control panel sends the Disarming Report

Codes to the monitoring station only when the partition is disarmed

following an alarm. Select the section that corresponds to the desired

partition and enable or disable option [7]:

9.16 Zone Restore Report Options

SECTION [3037]: OPTION [8]

(default = disabled) When disabled, the control panel sends the Zone

Alarm Restore report codes to the monitoring station when the Bell Cut-Off

Timer elapses (see section 8.2) or when the alarm is disarmed. When

Troubles and Restore Troubles: [3080]

Special System, Arming, Disarming and Alarm Reporting: [3081]

Access Code and Keyswitch Arming and Disarming

Partition 1: [3127] Partition 3: [3327] Partition 5: [3527] Partition 7: [3727]

Partition 2: [3227] Partition 4: [3427] Partition 6: [3627] Partition 8: [3827]

Zone Alarms and Alarm Restores

Partition 1: [3128] Partition 3: [3328] Partition 5: [3528] Partition 7: [3728]

Partition 2: [3228] Partition 4: [3428] Partition 6: [3628] Partition 8: [3828]

Tampers and Tamper Restores

Partition 1: [3129] Partition 3: [3329] Partition 5: [3529] Partition 7: [3729]

Partition 2: [3229] Partition 4: [3429] Partition 6: [3629] Partition 8: [3829]

Option Call: Option Call (select one only):

[1] Telephone Number 1 [5] Backup on Number 1

[2] Telephone Number 2 [6] Backup on Number 2

[3] Telephone Number 3 [7] Backup on Number 3

[4] Telephone Number 4 [8] Backup on Number 4

Partition 1: [3109] Partition 3: [3309] Partition 5: [3509] Partition 7: [3709]

Partition 2: [3209] Partition 4: [3409] Partition 6: [3609] Partition 8: [3809]

OFF OFF

Auto Test

Report

Period

(default)

After the number programmed (000 to 255 days,

default = 000) in section [3040], the control panel

transmits a report code at the time (00:00 to 23:59,

default = 00:00) programmed in section [3041].

OFF ON

Timed Test

Transmission

when Armed/

Disarmed

When disarmed: The control panel transmits the

code at regular intervals. Program the number of

minutes (000 to 255, default = 060) between

transmissions in section [3043].

When armed: The control panel transmits the test

report code at regular intervals. Program the

number of minutes (000 to 255, default = 005)

between each transmission in section [3042].

ON OFF

Hourly Test

Transmission

The control panel will transmit the test report code

every hour on the minute value programmed in

section [3041] (the last two digits). Note that the

first two digits of section [3041] will be ignored.

ON ON

Timed and

Hourly Test

Transmission

The test report code will be transmitted when any

of the conditions of the second and third options

listed above (options [3] = OFF and [4] = ON /

options [3] = ON and [4] = OFF) are met.

Partition 1: [3123] Partition 3: [3323] Partition 5: [3523] Partition 7: [3723]

Partition 2: [3223] Partition 4: [3423] Partition 6: [3623] Partition 8: [3823]

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 63 64

Komentáře k této Příručce

Žádné komentáře

SEKURE Paradox Digiplex DGP-610 Instalační příručka Strana 29

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu SEKURE Paradox Digiplex DGP-610