SEKURE Paradox Spectra 1686H Instalační manuál stáhnout pdf (Strana 39)

SPECTRA SERIES 37

[1] ON / [2] OF F: Alarm If System Armed

Upon line test failure, a TLM Trouble will appear in the keypads’ Trouble Display (see page 46) and if the system is

armed, the control panel will generate an alarm.

[1] ON / [2] ON : Silent Alarm Becomes Audible

Upon line test failure, a TLM Trouble will appear in the keypads’ Trouble Display (see page 46) and causes a silent

zone or si lent panic alarm to switch to audi ble.

8.20.1 TLM FAIL TIMER

Section [079]

016 to 255 x 2 seconds, Default = 32 seconds

If TLM does not detect the existence of a telephone line for the duration of this period, the control panel will

generate the condition(s) defined by the TLM options (see above).

PART 9: PROGRAMMABLE OUTPUTS

A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event

has occurred in the system. For example, a PGM can be used to reset smoke detectors, activate bells or strobe lights, open/

close garage doors and much more. When a PGM closes, the control panel supplies a ground to the PGM activating any

device or relay connected to it. When a PGM opens, the cir cuit opens from ground, therefore, cutting power to any devices

connected to it.

PGM1

1728EX and 1728 :

A program mable output that provides

up to 150mA

. Re fe r to PGM for 1728EX and 1728 on page 7.

1738EX and 1738 :

A program mable output that provides

up to 1A.

Refer to

Alar m Relay and PGMs for 17 38EX and 1738 on

page 7.

PGM2

1738EX and 1738 only: PGM2 is a programmable output that can provide up to 1A. PGM2 is designed to be used as a

Strobe Output. For information refer to PGM Strobe Options on page 38. For connections, r efer to Alarm Relay and PGMs for

1738EX and 17 38 on page 7.

Global PGM

The Global PGM allows you to use the control panel’s PGM Event List to activate PGMs located on a module or LCD keypad.

For example, if you enable a module’s “Follows Global PGM” option, the PGM on the module will activate whenever the event

programmed in section [124] occurs. Every PGM on every keypad and/or expansion bus module can be programmed to

follow the event(s) defined by the Global PGM.

9.1 PGM ACTIVATION EVENT

Sections [120], [122], and [124]

This feature allows you to program the control panel to activate a PGM when a specific event occurs in the system.

The PGM will remain in its active state until the programmed PGM Deactivation Event occurs or when the PGM

Delay period elapses (see page 38). For the Event List see the PGM Table in the Spectra 1728EX, 1728, 1738EX

and 1738 Programming Guide. PGM2 is available on the 1738EX and 1738 only. To program a PGM Activation

Event:

1) Enter section that represents the desired PGM. PGM1 = [120], PGM2 = [122], Global PGM = [124]

2) Enter the Event Group #.

3) Enter the Sub-Group #.

4) Enter the P art it io n #

01 = Partition 1

02 = Partition 2

99 = Both Partitions

The “AC Loss” PGM Event will only occur after the Power Failure Report Delay elapses (see page 36).

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 59 60

Komentáře k této Příručce

Žádné komentáře

SEKURE Paradox Spectra 1686H Instalační manuál Strana 39

Komentáře k této Příručce