SEKURE Paradox Spectra 1686H Instalační manuál Strana 44
- Strana / 60
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
42 REFERENCE & INSTALLATION MANUAL
10.13 PRINTER BUS MODULE SUPERVISION
Section [129 ]: General Op tion s
Option [8] OFF = Printer Bus Module Supervision Disabled (default)
Option [8] ON = Printer Bus Module Supervision Enabled
By enabling this option, the control panel will supervise the Printer Bus Module (APR3-PRT1) connected to the
Spectra bus. This means that whenever the Printer Bus Modul e is disconnected or is not communicating with the
control panel, the control panel will attempt to transmit the Module Fault report code programmed in section [210]
and the Module Loss Failure will appear in the keypads’ Tr oubl e Disp lay (see page 46).
Modules with the APR- prefix are compatible with Spectra (versions 2.0 and higher) and Digiplex. Modules
with the APR3- prefix are compatible with Spectra( versions 2.0 and higher), Digiplex and DigiplexNE.
10.14 ZONE EXPANSION BUS MODULE* SUPERVISION
Section [129 ]: General Op tion s
Option [4] OFF = Zone Expansion Bus M odul e Supervision Disabled (default)
Option [4] ON = Zone Expansion Bus Module Supervision Enabled
By enabling this option, the control panel will supervise the 4- or 8-Zone Expansion Bus Module (SPC/APR3-ZX4 or
SPC/APR3-ZX8) connected to the Spectra bus. This m eans that whenever the Zone Expansi on Bus Module is
disconnected or is not communicating with the control panel, the control panel will attempt to transmit the Module
Fault report code programmed in section [210] and the Module Loss Failure will appear in the keypads’ Trouble
Display (see page 46).
Modules with the APR- prefix are compatible with Spectra (versions 2.0 and higher) and Digiplex. Modules
with the APR3- prefix are compatible with Spectra( versions 2.0 and higher), Digiplex and DigiplexNE.
* The Zone Expansion Bus Module is not UL listed.
10.15 WIRELESS BUS MODULE SUPERVISION
Section [129 ]: General Op tion s
Option [5] OFF = Wireless Bus Module Supervision Disabled (default)
Option [5] ON = Wireless Bus Module Supervision Enabled
By enabling this option, the control panel will supervise the Wireless Bus Module (SPC-319) connected to the
Spectra bus. This means that whenever the Wireless Bus Module is disconnected or is not communicating with the
control panel, the control panel will attempt to transmit the Module Fault report code programmed in section [210]
and the Module Loss Failure will appear in the keypads’ Tr oubl e Disp lay (see page 46).
10.16 WIRELESS TRANSMITTER LOW BATTERY SUPERVISION
Section [129 ]: General Op tion s
Option [6] OFF = Wireless Transmitter Low Battery Supervision Disabled (default)
Option [6] ON = Wireless Transmitter Low Battery Supervision Enabled
When option [6] in section [129] is enabled and the battery voltage of a wireless transmitter (motion detector or
contact switch) has dropped below recommended limits, the control panel will attempt to transmit the Wireless
Transmitter Low Battery report code programmed in section [210] and the Wireless Transmitter Low Battery Failure
will appear in the keypads’ Trouble Display (see page 46).
10.17 WIRELESS TRANSMITTER SUPERVISION OPTIONS
Section [1 32 ]: Zone Option s
Please note that the Supervision Option on the 900MHz Wireless Bus Module must be enabled (see section 10.15).
[7] OFF / [8] OF F: Supervision Failure Recognition Disabled (default)
When a tamper occurs on a wireless transmitter zone in a disarmed system, the control panel will display the zone
as open in the keypad display, but will not generate an alarm. When it occurs on in an armed system, the control
panel will follow the zone's Alarm Types setting (see page 21). This option is not permitted on UL systems.
- SPECTRA CONTROL PANELS V2.1 1
- TABLE OF CONTENTS 3
- LIST OF TABLES 4
- PART 1: INTRODUCTION 5
- PART 2: INSTALLATION 6
- 2.2 EARTH GROUND 7
- 2.3 AC POWER 8
- 2.4 BACKUP BATTERY 8
- 2.6 TELEPHONE LINE CONNECTION 8
- 2.7 BELL OUTPUT CONNECTION 9
- 2.9 SINGLE ZONE INPUTS 10
- 2.12 KEYSWITCH CONNECTIONS 11
- PART 3: PROGRAMMING METHODS 12
- SPECTRA SERIES 11 13
- PART 4: ACCESS CODES 15
- 4.1 ACCESS CODE LENGTH 16
- 4.4 USER CODE OPTIONS 16
- 4.6 DURESS CODE 17
- 4.5 LOCK MASTER CODE 17
- PART 5: ZONE PROGRAMMING 18
- 5.4 ZONE PROGRAMMING 19
- 5.5 ZONE DEFINITIONS 20
- 5.7 ZONE PARTITION ASSIGNMENT 22
- 5.8 ZONE OPTIONS 22
- 5.9 ZONE SPEED 24
- 5.10 EOL ZONES 24
- 6.1 SWITCH TO STAY AR MING 25
- 6.2 STAY ARMING WITH DELAY 25
- 6.6.1 AUT O-ARM TIMER 26
- 6.8 AUTO-ARMING OPTIONS 27
- 6.9 ONE-TOUCH ARMING 27
- 6.10 EXIT DELAY 27
- PART 7: ALARM OPTIONS 28
- 7.3 TAMPER RECOGNITION 29
- 7.4 KEYPAD PANIC OPTIONS 29
- 7.5 PANIC LOCKOUT TIMER 30
- SPECTRA SERIES 29 31
- 8.2 REPORT CODES 32
- Sections [208] to [210] 34
- Sections [211] to [213] 34
- 8.4 PARTITION ACCOUNT NUMBERS 35
- 8.5 REPORTING FORMATS 35
- 8.6 PAGER DELAY 36
- 8.7 EVENT CALL DIRECTION 36
- SPECTRA SERIES 35 37
- PART 9: PROGRAMMABLE OUTPUTS 39
- PART 10: SYSTEM SETTINGS 41
- 10.6 SYSTEM REAL-TIME CLOCK 42
- 10.7 CLOCK ADJUST 42
- SPECTRA SERIES 43 45
- 11.1 PANEL ANSWER OPTIONS 46
- 11.2 PANEL IDENTIFIER 46
- 11.3 PC PASSWORD 46
- 11.4 PC TELEPHONE NUMBER 46
- 11.5 CALL WINLOAD SOFTWARE 47
- 11.6 ANSWER WINLOAD SOFTWARE 47
- 11.8 CALL BACK WINLOAD 47
- PAR T 12: USER OPERATION 48
- 12.2 PROGRAMMING ACCESS CODES 49
- 12.4 REGULAR ARMING 50
- 12.5 STAY ARMING 50
- 12.6 INSTANT ARMING 50
- 12.7 FORCE ARMING 51
- 12.9 ONE-TOUCH ARMING 51
- 10-ZONE LED KEYPAD: 52
- 12.15 KEYPAD MUTING 53
- FCC WARNINGS 54
- SPECTRA SERIES 53 55
- SPECTRA SERIES 55 57
- IN CANADA 02/2003 17X8-EI07 60
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.095 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce