SEKURE DGP2-641 Instalační manuál stáhnout pdf (Strana 27)

IGIPLEX

NE C

ONTROL

ANEL

8.1 B

ELL

ALARM

UTPUT

(Default = only option [1] enabled) When an alarm condition is detected in a

partition, the control panel can toggle the on-board

BELL

output enabling

any bells or sirens connected to it. In section [3032] enable the option to

enable the bell output in the desired partition (off = disabled):

8.2 B

ELL

OFF

IMER

(Default = 004) After an audible alarm, the bell or siren will stop once the

partition is disarmed or when the Bell Cut-Off Timer has elapsed. Enter any

value between 001 and 255 minutes:

8.2.1 No Bell Cut-Off on Fire Alarm

(Default = disabled) The control panel can disable the Bell Cut-Off Timers

when alarms are generated from zones defined as Standard or Delayed

Fire Zones (see section 5.3). The

BELL

output will remain enabled until a

user disarms the partition in alarm.

8.2.2 Recycle Alarm Rate

(Default = 000) The control panel re-verifies the zone status during an

alarm at a programmed rate once the Bell Cut-Off Timer and the Recycle

Delay elapse. If open zones remain, the control panel will regenerate the

alarm. Enter the number of times from 001 to 255 (000 = no limit) in one

armed period that the control panel will re-verify the zone status:

8.2.3 Recycle Delay

(Default = 000) The Recycle Delay is the amount of time the control panel

will wait after the Bell Cut-off occurs before re-verifying the zone status.

Program the Recycle Delay from 001 to 255 minutes (000 = disabled):

8.3 W

IRELESS

RANSMITTER

UPERVISION

PTIONS

The Supervision feature must be enabled in the Omnia Wireless

System (OMN-RCV3) for this feature to function.

ARMED

PARTITION

When the control panel detects a Supervision Loss (wireless receiver no

longer receiving signals from a wireless transmitter), the control panel

generates an alarm unless the Wireless Transmitter Supervision Options

are disabled. Alarms are silent or audible depending on individual zone

settings.

DISARMED

PARTITION

When the control panel detects a Supervision Loss, the control panel

follows the programmed settings:

8.3.1 Supervision Bypass Options

(Default = disabled) With option [3] enabled in section [3034], the Wireless

Transmitter Supervision Options will follow the zone's bypass definition.

This means that the control panel will not perform any action if a

supervision loss occurs on a bypassed zone. With option [3] disabled, the

control panel will ignore the bypass definition and will follow the option set

in section 8.3 if a supervision loss occurs on a bypassed zone.

8.4 P

OLICE

ODE

IMER

(Default = 000) If an alarm condition occurs on a zone, the control panel

generates an alarm and triggers the Police Code Timer. The Police Code

Timer requires confirmation of the alarm situation within the delay before

sending the Police Code programmed in [3934]. The Police Code will only

be sent if one of the following conditions occurs during the delay:

1) An alarm occurs on another zone.

2) The zone in alarm restores and reoccurs.

Key in the desired 3-digit delay value (001 to 255 minutes, 000 = disabled)

into the section corresponding to the desired partition:

8.5 T

AMPER

ECOGNITION

PTIONS

ARMED

PARTITION

When the control panel detects a tamper or wire fault on a zone or on an

expansion module with GuardWall technology, the control panel always

generates an alarm unless Tamper Recognition is disabled. Alarms are

silent or audible depending on individual zone settings.

DISARMED

PARTITION

When the control panel detects a tamper or wire fault on a zone or on an

expansion module with GuardWall technology, the control panel follows the

programmed settings:

Partition 1: Option [1] Partition 5: Option [5]

Partition 2: Option [2] Partition 6: Option [6]

Partition 3: Option [3] Partition 7: Option [7]

Partition 4: Option [4] Partition 8: Option [8]

Partition 1: [3113] Partition 3: [3313] Partition 5: [3513] Partition 7: [3713]

Partition 2: [3213] Partition 4: [3413] Partition 6: [3613] Partition 8: [3813]

Partition 1: [3117] Partition 3: [3317] Partition 5: [3517] Partition 7: [3717]

Partition 2: [3217] Partition 4: [3417] Partition 6: [3617] Partition 8: [3817]

Partition 1: [3116] Partition 3: [3316] Partition 5: [3516] Partition 7: [3716]

Partition 2: [3216] Partition 4: [3416] Partition 6: [3616] Partition 8: [3816]

Option Feature Description

[1] [2]

OFF OFF

Disabled

(Default)

Displays zone open on the keypads, but will

not generate an alarm or trouble.

Not permitted on UL systems.

ON OFF

Trouble Only

The control panel displays Zone Fault in the

Trouble Display and transmits the defined

report code (see section 9.2).

OFF ON

Silent Alarm

The control panel displays Zone Fault in the

Trouble Display, transmits the defined report

code (see section 9.2), and generates a silent

alarm (no bells/sirens).

ON ON

Audible Alarm

The control panel displays Zone Fault in the

Trouble Display, transmits the defined report

code (see section 9.2), and generates an

audible alarm.

Partition 1: [3118] Partition 3: [3318] Partition 5: [3518] Partition 7: [3718]

Partition 2: [3218] Partition 4: [3418] Partition 6: [3618] Partition 8: [3818]

Option Feature Description

[5] [6]

OFF OFF

Disabled

(Default)

Displays zone open on the keypads, but will

not generate an alarm or trouble.

Not permitted on UL systems.

ON OFF

Trouble Only

The control panel displays Zone Fault in the

Trouble Display and transmits the defined

report code (see section 9.2).

OFF ON

Silent Alarm

The control panel displays Zone Fault in the

Trouble Display, transmits the defined report

code (see section 9.2), and generates a silent

alarm (no bells/sirens).

ON ON

Audible Alarm

The control panel displays Zone Fault in the

Trouble Display, transmits the defined report

code (see section 9.2), and generates an

audible alarm.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 65 66

Komentáře k této Příručce

Žádné komentáře

SEKURE DGP2-641 Instalační manuál Strana 27

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu SEKURE DGP2-641