SEKURE DGP2-641 Instalační manuál stáhnout pdf (Strana 36)

34 R

EFERENCE

& I

NSTALLATION

ANUAL

A PGM is a programmable output that toggles to its opposite state (i.e. a

normally open PGM will close) when a specific event occurs in the system.

For example, a PGM can be used to reset smoke detectors, activate strobe

lights, open/close garage doors and much more.

When a PGM closes, the control panel supplies a ground to the PGM

activating any device or relay connected to it. When a PGM opens, the

circuit opens from ground, therefore not providing any power to the devices

connected to it. The control panel provides a maximum of 100mA to PGM1

and 5A to PGM2 and PGM3. PGM1 is a normally open transistor output

and PGM2 and PGM3 are normally open or normally closed 5A relays. For

details on how to connect a relay to a PGM, please refer to section 3.8 on

page 9.

11.1 PGM A

CTIVATION

VENT

The PGM Activation Event determines which event will activate the PGM.

The Event Group specifies the event, the Feature Group identifies the

source, and the Start # and End # sets the range within the Feature Group

(see PGM Programming Table in the Programming Guide).

For example, the control panel can activate PGM1 when the partition is

armed by User Access Codes 256 to 260. Therefore:

Event Group section [0910] = 010 “Arming with User Code”

Feature Group section [0911] = 001 “User Codes 256 to 511”

Start # section [0912] = 000

End # section [0913] = 004

Enter the sections that correspond to the Event Group, Feature Group,

Start # and End # of the desired PGM and enter the desired 3-digit number

from the PGM Programming Table:

11.2 PGM D

EACTIVATION

PTION

Once the PGMs are activated (see section 11.1), they can deactivate when

another event occurs or after a period of time. The PGM Deactivation

Option determines which method is used, the PGM Deactivation Event (see

section 11.4) or the PGM Timer (see section 11.5). Enter the section that

corresponds to the desired PGM and enable or disable option [1] (default =

PGM Deactivation Event):

11.3 F

LEXIBLE

PGM D

EACTIVATION

PTION

The PGM Deactivation Option (see section 11.2) must be set to PGM Timer

for this feature to function. The Flexible PGM Deactivation Option uses the

benefits of both the PGM Deactivation Event (see section 11.4) and the

PGM Timer (see section 11.5). When option [3] is enabled and the PGM is

activated (see section 11.1), it will deactivate when either the PGM

Deactivation Event occurs or the PGM Timer elapses, whichever happens

first.

For example, the PGM activates and the PGM Timer is set for 5 minutes.

However, the PGM Deactivation Event occurs before 5 minutes ends so the

PGM deactivates.

Enter the section corresponding to the PGM and enable option [3] (default

= disabled):

11.4 PGM D

EACTIVATION

VENT

The PGM Deactivation Event determines which event will return the PGM

to its original state. The Event Group specifies the event, the Feature

Group identifies the source, and the Start # and End # determine the range

within the Feature Group. The complete PGM Programming Table appears

in the Programming Guide.

For example, to deactivate PGM1 when zone 3 opens, program:

Event Group section [0914] = 001 “Zone is Open”

Feature Group section [0915] = 000 “Zone Numbers”

Start # section [0916] = 003

End # section [0917] = 003

Enter the sections that correspond to the Event Group, Feature Group,

Start # and End # of the desired PGM and enter the desired 3-digit number

from the PGM Programming Table.

11.5 PGM T

IMER

When the PGM Deactivation Option (see section 11.2) is enabled, the PGM

Timer determines how many seconds or minutes (see section 11.5.1) the

PGM remains activated before it returns to its original state.

Enter the section that corresponds to the desired PGM and enter a value

from 001 to 255 (default = 005). The value entered is either in seconds or

minutes as determined by the PGM Time Base Selection (see section

11.5.1).

11.5.1 PGM Time Base Selection

The PGM Time Base Selection determines whether the PGM Timers in

sections [0918], [0928] and [0938] are in minutes or seconds (default =

seconds). Enter the section corresponding to the desired PGM and enable

or disable option [2]:

11.6 PGM1 B

ECOMES

WIRE

MOKE

ETECTOR

NPUT

(Default = disabled) Enabling option [1] in section [3030] sets PGM1 to act

as a zone input for two-wire smoke detectors. When programming Zone

Numbering (see section 5.1), the control panel will recognize PGM1 as

input number 255. For two-wire smoke detector connections, please refer

to section 3.17.1 on page 14

11.7 PGM T

EST

ODE

Entering sections [0901] to [0903] activates the corresponding PGM for 8

seconds to verify if the PGM is functioning as desired.

Event Group Feature Group Start # End #

PGM 1: [0910] [0911] [0912] [0913]

PGM 2: [0920] [0921] [0922] [0923]

PGM 3: [0930] [0931] [0932] [0933]

PGM 1: [0919] Option Feature

PGM 2: [0929] [1]

PGM Timer

PGM 3: [0939] [1]

OFF

PGM Deactivation Event

PGM 1: [0919] PGM 2: [0929] PGM 3: [0939]

Event Group Feature Group Start # End #

PGM 1: [0914] [0915] [0916] [0917]

PGM 2: [0924] [0925] [0926] [0927]

PGM 3: [0934] [0935] [0936] [0937]

PGM 1: [0918] PGM 2: [0928] PGM 3: [0938]

PGM 1: [0919] Option Feature

PGM 2: [0929] [2]

Minutes

PGM 3: [0939] [2]

OFF

Seconds

PGM 1: [0901] PGM 2: [0902] PGM 3: [0903]

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 65 66

Komentáře k této Příručce

Žádné komentáře

SEKURE DGP2-641 Instalační manuál Strana 36

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu SEKURE DGP2-641